Request a Quote

Give us a call today or click here
for a free quote

717.656.0513

339 Monterey Rd.,
Bird In Hand, PA 17505

Residential Garage Doors PA

Commercial Openers

T Automatic Opener

T - Industrial-Duty Trolley Operator for Standard Lift Sectional Doors
Model T is an industrial-duty trolley operator for standard lift section doors. It features a low profile and industrial ball bearings on the output shaft.




LOGIC 4.O TECHNOLOGY (L4)
Added Value

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation

  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes

  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors.

  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators

  • All high-voltage connections have been removed from the board for safety and ease of service

  • Diagnostic LEDs speed installation and troubleshooting

  • Motor direction jumper lets you change motor direction by simply moving a jumper

STANDARD FEATURES
Motor: 
Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-RPEN4, CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI safety edge interface. Operators are pre-wired to accept a sensing edge, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Ball bearings on output shaft; heavy-duty, oil-filled bushings on reduction shafts.

Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/3 and 1/2 HP units.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Rail Assembly: High-strength dual L-rail track with nylon quiet-gliding chain guides on rail spacers for quiet, smooth operation.

Warranty: 2-year warranty.


MT Automatic Opener

MT - Medium Duty Trolley Operator for Standard Lift Sectional Doors
Model MT is a Medium-Duty Logic trolley operator for standard lift sectional doors. It features a high-starting torque motor, a compact design, quick-gliding rail spacers and a quick-mount swivel header bracket.


MEDIUM-DUTY LOGIC TECHNOLOGY

Added Value

  • UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board

  • Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation

  • Programmable C2 or B2 wiring options (B2 requires CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI)

  • Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI)

  • Integrated 90-second maximum run timer

  • UL325-2010 Monitored Entrapment Capability

  • Monitored protection against transient overvoltage conditions

  • 3-button control station included

STANDARD FEATURES

Motor: Powerful 1/2 HP, single phase motor with instant reverse and internal automatic reset thermal overload. Removable without affecting limit switch settings.

Auxiliary Reversal System: PDesigned to protect the door and door operator from damage; if a closing door strikes an obstruction, the Auxiliary Reversal System will detect the slip of the clutch and reverse the door to the full open position. This system is not a substitute for a safety sensing device such as a photo cell or reversing edge.

Rail Assembly: High strength dual L-rail track with exclusive nylon quiet gliding chain guides on rail spacers for quiet, smooth operation. Includes quick-mount header bracket which provides fast, swing-up installation.

Operator/Motor Control: Solid-state Medium-Duty circuit board.

Control Circuit: 24V NEC Class 2.

Emergency Disconnect: Spring-loaded disconnect for emergency manual operation.

Push Button Station: 3-button station for OPEN/CLOSE/STOP functions is standard for all operators. Controls with 1, 2 and 3 buttons are available.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with baked-on powder coat finish, all reduction sprockets drilled and pinned to shafts.

Bearings: Heavy-duty, oil filled bearings.

Radio Receiver: 315MHz radio receiver is integral to the Medium-Duty logic board. Accepts up to 20 Security+® remote controls and unlimited DIP switch remote controls.

Friction Clutch:
Adjustable friction clutch helps protect against damage to the door and operator should the door meet an obstruction. Works in conjunction with the Auxiliary Reversal System.

Warranty:
2-year warranty.



J Automatic Opener

J - Industrial Duty Jackshaft Operator
Model J is an industrial-duty jackshaft operator. It features a removable hinged electrical box cover, a continuous-duty high-starting torque motor, industrial ball bearings on the output shaft and a universal mount frame design.



LOGIC 4.0 TECHNOLOGY (L4)

Added Value

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation

  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes

  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-RPEN4, CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface

  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation

  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes

  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-RPEN4, CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface

  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators

  • All high-voltage connections have been removed from the board for safety and ease of service

  • Diagnostic LEDs speed installation and troubleshooting

  • Motor direction jumper lets you change motor direction by simply moving a jumper

Available Plug-in Options for Logic 4.0 (L4)

Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices.  Features both normally open and closed contacts that actuate in conjunction with limit switches.

STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: First-stage heavy-duty 5L V-belt; second and third stages #48 chain; #50 drive chain.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Industrial ball bearings on a 1" output shaft; heavy-duty oil-filled iron bearings on reduction shafts.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

PosiLock® Mechanical Brake System: Self-locking mechanical reduction system that functions as a holding brake.

Warranty:
2-year warranty.


MJ Automatic Opener

MJ - Medium-Duty Jackshaft Operator
Model MJ is a Medium Duty Logic jackshaft operator. It features a compact design, an adjustable friction clutch, a standard solenoid brake and a high-starting torque motor.




MEDIUM-DUTY LOGIC TECHNOLOGY
Added Value

  • UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board

  • Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation

  • Programmable C2 or B2 wiring options (B2 requires CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI)

  • Integrated timer-to-close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI)

  • Integrated 90-second maximum run timer

  • UL325-2010 Monitored Entrapment capability

  • Monitored protection against transient overvoltage conditions

  • 3-button control station included


STANDARD FEATURES
Motor:
Powerful 1/2 HP, 115V single phase motor with instant reverse and internal automatic reset thermal overload. Removable without affecting limit switch settings.

Operator/Motor Control: Solid-state Medium-Duty circuit board.

Control Circuit: 24V NEC Class 2.

Brake: Heavy-duty solenoid actuated brake standard.

Drive Reduction: First stage heavy-duty 4L V-belt; second stage and third stages #48 chain.

Push Button Station: 3-button station for OPEN/CLOSE/STOP functions is standard for all operators. Controls with 1, 2 and 3 buttons are available.

Construction: NEMA 1 Type electrical box, heavy-duty 11-gauge steel frame with durable baked-on powder coat finish, all reduction sprockets drilled and pinned to shafts.

Friction Clutch:
Adjustable friction clutch helps protect against major damage to door and operator should the door meet an obstruction.

Radio Receiver: 315MHz radio receiver is integral to the Medium-Duty logic board. Accepts up to 20 Security+® remote controls and unlimited DIP switch remote controls.

Warranty: 2-year warranty.


Testimonials

"Appreciated the service very much. Thank you."
E. Smucker

"Thank you so much for fixing my garage door. I will promote you as a highly reliable service. Service like yours has become a rare commodity. Blessings"
C. Martin

"Thank you for the prompt & courteous services. I will continue to use your company in the future and recommend your business to family & friends."
M. Lopane

We install:

General Doors
Artisan doors
LiftMaster